PUMPS

We can supply a broad range of pumps in any material configuration to suit each application, either from our own stocks, or source pumps at competitive prices for clients, thus saving time and money.

Submersible Pumps

Pumps fitter with screw impellers of the non clog design suitable for raw sewage and other fibrous matter.
Pumps fitter with recessed or torque – flow impellers suitable for solids handling over 80mm, raw sewage or stringy matter.
Portable drainage pumps for general industry, mining and site work use.
Smaller stainless steel pumps for domestic or general drainage which can be supplied as solids handling or drainage pumps.
Hard metal slurry pumps fitted with abrasion resistant material.

Centrifugal & General Pumps

Pumps fitter with screw impellers of the non clog design suitable for raw sewage and other fibrous matter.
Pumps fitter with recessed or torque – flow impellers suitable for solids handling over 80mm, raw sewage or stringy matter.
Portable drainage pumps for general industry, mining and site work use.
Smaller stainless steel pumps for domestic or general drainage which can be supplied as solids handling or drainage pumps.

Level Regulators

Cable length of 6m, 10m and 20m in neoprene and hypalon,
With mercury contact switch (of metal).
With a micro switch (no mercury).

Becon Aquapure Portable Raw Water Treatment Plants

Our companies supply our Becon Aquapure portable raw water treatment plants on a turnkey basis including design, construction and installation anywhere in South Africa. Each plant is designed to suit specific raw water conditions.
We supply the range of MAZZEI INJECTORS of the venturi differential pressure type to inject liquids or gases into a pressurised or open system. these injectors are manufactured from materials such as polypropylene, kynar or stainless steel to suit any situation such as:

  • Fertiliser Transfer into spray or irrigation lines
  • Gas Injection: ozone, oxygen, chlorine, nitrogen
  • Liquid Injection: chemicals, Polymers, disinfection
  • Aeration: BOD/TOC reduction, oxygenation, odour control
Custom designed to individual requirements for hotels, multi-story flat complexes, etc.
Contact us to find out more on our Flowline Verticle Aerator.

Pressure Boosting

  • 2 to 6 pumps per system
  • Continuous control operation of the base load pump via frequency converter integrated in the CC controller version
  • 2 to 6 vertical high-pressure multistage centrifugal pumps switched in parallel
  • In the VR version, each pump is equipped with an integrated VSD
  • Units supplied, complete with manifolds and all required valves and sensors mounted on common basE
  • Stainless steel / Cast Iron in-line design
  • IE2 standard three phase motor, 2 pole, AC
  • Single phase AC motor with integrated thermal motor protection
  • 16 Bar & 25 Bar versions available
  • EPDM & Viton(dependend on size) seal versions available Helix
  • Stainless steel / Cast Iron in-line design
  • ≥ 7.5kW – IE3 standard three phase motor, 2 pole, AC
  • High efficient hydraulic
  • 16 Bar & 25 Bar versions available
  • Stainless steel pump in monobloc design
  • Threaded connection
  • Single phase or three phase AC motor
  • Single phase AC motor with integrated thermal motor protection
  • All parts that come in contact with the fluid are made of stainless steel 1.4301 (AISI 304) or 1.4404 (AISI 316)
  • EPDM(AISI 304) & VITON(AISI 316) seals available
  • Stainless steel shaft & stages in monobloc design
  • Cast iron threaded suction/discharge connections
  • Single phase or three phase AC motor
  • EPDM mechanical seal & O – rings
  • Directly flanged motor
  • Thermal motor protection switch for single phase AC motor (1~230V / 3~400V)
  • Low noise
  • Ideal as a base-load pump for rainwater utilisation
  • Self priming up to 8 metres *
  • At sea level
  • With or without carrying frame
  • For single phase AC motor (1~230V)
  • Connection cable with plug
  • On / Off switch
  • Thermal motor protection switch
  • Self priming up to 8 metres – At sea level

Drainage

  • Ready to plug & play
  • Motor monitoring via temperature
  • Sheath current cooling
  • Connection cable
  • Float switch
  • Non-return valve enclosed (depending on type)
  • TMW with turbulator for constantly clean pump sump
  • Easy installation
  • Vortex & Cutter impeller available
  • Cast iron & 316 S/Steel construction available
  • Built – in motor protection as standard
  • Connection cable
  • Float switch – 230V only
  • Can handle solids up to 50mm
  • Cost effective
  • Easy installation
  • Stationary & Portable design
  • Wet installation only
  • Flow rate up to 22m3/h
  • Internal/External macerator available
  • 10m lead out cable as standard
  • Ex – rated in accordance with ATEX as standard
  • Stainless Steel & Cast Iron construction available
  • Automatic Lifting
  • Macerator as standard
  • Flow rate from 0.8m3/h up to 3.2m3/h
  • Built in NRV
  • Connection for toilet/basin/shower
  • Built-in active carbon filter with overflow protection

Circulation

  • Permanent temperature range -10⁰C to +110⁰C
  • Pre-selectable speed stages for power adjustment
  • Mains connection 1~230V, 50Hz or 3~400V in the TOP S range
  • Maximum operating pressure 10 bar (PN 16 on special request)
  • Available in Red Bronze on request
  • Available in Dual Head on request
  • Protection class IP 44
  • Permanent temperature range -10⁰C to +110⁰C
  • Pre-selectable speed stages for power adjustment
  • Maximum operating pressure 10 bar
  • Avail in Red Bronze on special request
  • Avail in Dual Head on special request
  • High efficiency IE4 motor
  • Integrated electronic power adjustment
  • Compact and space saving

Control

  • Electronically flow and pressure controller
  • Built – in dry run protection
  • In-Line Design
  • Mains connection 1~230V- 50Hz
  • 1” inlet & outlet
  • Built in NRV
  • Flow Rate – Max 10m3/h
  • Max operating pressure – 6Bar
  • Temperature Range – 0⁰C to 60⁰C
  • Protection Class – IP65
  • Electronically flow and pressure controller by means of Variable Speed Drive
  • Pressure/flow Monitoring
  • In-Line Design
  • Mains connection 1~230V- 50Hz & 3 ∼230V – 50Hz
  • 1” inlet & outlet
  • Built in NRV
  • Max operating pressure – 6Bar
  • Temperature Range – 0⁰C to 40⁰C
  • Protection Class – IP65
  • Built in EMC Filter
  • Float Switch input available for dry run protection

Air-Conditioning

  • Cast iron pump
  • Stainless steel shaft
  • Cast iron & Bronze impeller available
  • Mechanical seal
  • Models from 32-125 up to 150-400 – Locally Available
  • Models from 150 – 500 up to 300-400 – Special Request
  • Flows up to 1500m3 / hour
  • Head up to 145m at 2900 rpm

Fire-Fighting

  • Diesel, Electric & Jockey pump available
  • EN 12845 Standard
  • Designed for Sprinklers, Hydrants, Hose Reels
  • Simple Operation
  • From DN65 up to DN250
    Flow up to 450m3/h
    Pressurize up to 140m
    Compact and space saving

OUR BRANDS